Top 10 typical forklift mishaps ， forklift operation ought to focus on these matters ！.

Don't take too lightly the forklift at the workplace. If the procedure is bad, there will certainly be major accidents in mins, and there are several crashes including forklifts.

Case 1: The forklift freight blocked the vehicle driver's view, and the individual ahead could not be found, causing a rolling crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy goods, the staff members used their body weight as the weight, which practically triggered casualties.
Instance 3: The size of the forklift freight surpasses the allowable width of the course and holds on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding and surrender throughout a turn.
Instance 5: The forklift chauffeur did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift raises the personnel illegally, the forklift driver does not wear the safety belt, the forklift lifter drops and the vehicle driver is squashed when the forklift rolls over.
Situation 7: The forklift chauffeur did not put on a safety belt and dropped from the car when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Start.
1. Before starting, observe the environments, and after verifying that there are no obstacles that hinder the safety and security of driving, beep the horn first and afterwards begin.
2. For vehicles with hydraulic (air pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be secure prior to starting.
3. When the forklift begins with a load, the vehicle driver needs to first verify that the load is steady and trusted.
4. The begin must be slow-moving and steady.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the mast ought to be tilted backwards. .
2. Do not raise the fork expensive when driving. When getting in and leaving the work site or while driving, beware that there will certainly be no barriers overhead. When the tons is taking a trip, the fork needs to not be elevated too expensive, which will affect the security of the forklift. .
3. After discharging, the fork ought to be lowered to the regular driving setting prior to driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be issued initially. High-speed sharp turns are banned. High-speed doglegs will certainly create the lorry to lose lateral security and topple. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is prohibited to brake suddenly while driving with lots unless there are special circumstances.
6. When the forklift is running, it needs to obey the traffic rules in the manufacturing facility and must keep a particular security range from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest setting that does not prevent the driving, and the gantry needs to be properly slanted back. The tons will not be increased except when stacking or filling. .
8. The elevation of the tons must not block the chauffeur's view. In unique conditions, when the product influences the forward vision, drive at a reduced rate when turning around.
9. It is restricted to turn on the ramp, neither to drive across the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it has to drive safely at a low speed when going into the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is forbidden for employees to depend on the fork to hold things and play a balancing duty. .
12. If troubles are found, they will certainly be fixed and reported in a prompt fashion, and they will never ever operate with illnesses or conceal them.

packing and unloading.
1. When fork-loading things, the range in between both forks ought to be changed as required to make the tons of the two forks well balanced and not skewed, and one side of the item need to be against the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or pull. In unique circumstances, safety and security warning signs must be set up to remind bordering pedestrians. .
3. In the process of packing and unloading items, the forklift has to be braked with the brake. .
4. The rate of the car should be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as feasible under the tons, and it ought to be kept in mind that the fork suggestion ought to not touch various other goods or objects. The load needs to be stabilized with minimal back tilt of the gantry to ensure that the tons does not move in reverse. The pole can be tilted forward slightly when the load is reduced to permit easy positioning of the tons and extraction of the forks. .
6. It is prohibited to fork products at high speed and ram hard items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude procedures to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slip, place, round or roll things. .
10. It is not enabled to use forks to choose, transform pallet discharge.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork impend. Prior to leaving the forklift, you must unload the goods or reduced the fork frame.
2. Draw the hand brake deal with to dead or depress the parking brake button.
3. The engine is switched off and the power is removed. (Except for special situations, such as the vehicle driver does not leave the car's line of sight and does not go beyond 1 min).
4. Eliminate the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and gas, lubing oil and air conditioning water need to be added.
2. Check the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, check whether the pressure and temperature are typical.
5. After the forklift is running, the external leakage needs to likewise be examined Stand-on Electric Pallet Stacker and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the cars and truck;.
2. When you encounter someone in front of you throughout driving, you should send a signal at a distance of 5 m;.
3. The driving speed in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m above the ground;.
5. The turning should not be also sharp Stand-on Electric Pallet Stacker to prevent the propensity of " totally free switching";.
6. Running up and down the incline ought to be slow and consistent, and no activating the slope is allowed.
7. Do not drive throughout the slope. When the slope is higher than 10%, the automobile should be driven backwards when going downhill;.
8. When the forklift employees carry the goods and move forward, if they come across big or heavy goods and most likely to the vehicle driver's view, they should take the turning around exercise
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork operation is not allowed.
2. It is not enabled to lift the goods for cross country driving.
3. It is not permitted to pick up the goods by turning over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not permitted to utilize inertia force to get the goods.
6. It is not allowed to use stopping pressure to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to work on the pallet or fork, and it is purely prohibited to stand under the fork after the fork is increased.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Contours, slim roadways, railway crossings;.
2. Areas with a longitudinal incline above 5%.
3. When there is an challenge on one side of the road, the contrary side of the area with the exact same length as the barrier ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844